Izuma Device Management Client error recovery mechanism

Connectivity Error Handling

Device Management Client handles error recovery on behalf of applications, thereby providing a seamless connectivity experience and recovery from temporary network break issues or disruptions to Device Management services. Connectivity between a client and Device Management encompasses network connectivity, CoAP level connectivity and client-service level connectivity (including, for example, handling client certificate expiry or renewal).

The logic handling reconnection to Device Management:

• Establishes a secure network connection.
• Registers to Device Management.
• Resends CoAP messages. More information about resending is in the CoAP specification.

This section explains what kind of connectivity errors an application may receive, what they mean and how the Device Management Client handles them.

Note: Some errors may need to be handled by the user or the application.

Reconnection attempt intervals

Device Management Client tries to establish a new connection to the server with incremented reconnection attempts:

1. The client picks a random initial reconnection time between 2 to 10 seconds (to prevent multiple clients trying to connect to Device Management at the same time after a possible service break).
2. It tries reconnection after this initial time.
3. If the connection fails, the client returns an appropriate error to the application.
4. The client continues retrying the connection to Device Management with an increased reconnection time. Every failed reconnection attempt increments the reconnection time by a factor of two, continuing until the reconnection time reaches one week. For example, if the client picks the initial reconnection time of 5 seconds, it tries to reconnect at 5, 10, 20, 40, 80... seconds up to one week.
5. The reconnection time does not increase above one week; the client will attempt to reconnect once a week until it reconnects or the device stops operating.

Every successful reconnection resets the reconnection time; if there is another failure, the reconnection attempts will begin with the original reconnection time.

Error codes

Failed connection attempts can return different error codes to a client application. The following list explains the error codes and proposes possible fixes. The actual enumerations for these error codes are located in mbed-cloud-client/mbed-cloud-client/MbedCloudClient.h.

ConnectBootstrapFailed

• Bad request Account device quota reached

  Device Management Client failed to successfully bootstrap to Device Management and cannot retrieve credentials for the Device Management service. This normally happens when you are using a developer certificate, and have already created 100 devices with that certificate, or if you have reached your account's device bootstrap limit.

  To fix this issue, delete some devices through Device Management Portal. Device Management Client continues to retry to bootstrap, and will connect as soon as there is room for new devices.

• Bad request (no details)

  A generic failure that could be the result of a missing certificate, lack of access rights, or failure to upload your CA certificate to the Device Management server.

  Alternatively, your certificate may not be enabled (in other words, it might be blacklisted). Please, ask your administrator to enable it.

ConnectInvalidParameters

The application has entered one or more wrong parameters at registration. Normally, this error occurs when the application provides an invalid Device Management URL (the accepted CoAP format is coap:://<URL>:5684), device name or account ID (for example, a parameter longer than 64 characters).

ConnectNotRegistered

The application tried to call close() without the client being in the registered state.

ConnectTimeout

Device Management is not responding to the client's registration attempts. This normally happens when the client cannot finish a successful registration within three minutes and there are no network issues during that time.

ConnectNetworkError

There is a network level issue between the client and Device Management server causing a connection break. The client returns this error when trying to register, or if it loses connection while already registered. It falls back to the reconnection logic and attempts to recover from the lost connection by re-registering itself.

ConnectResponseParseFailed

The application received a malformed CoAP message from the server, which it failed to parse. This can happen if a third party server implementation has mismatching CoAP library implementations, and should not happen with Device Management services.

ConnectMemoryConnectFail

The client failed to store the Device Management device credentials it received during bootstrap. This can happen if the client cannot create a CoAP message due to low memory.

ConnectNotAllowed

The application tried to call an API that the client cannot handle at that stage. For example, the application tried to call keep_alive() before setup().

ConnectSecureConnectionFailed

There was a (D)TLS level failure during the registration phase. This can happen because of an expired device certificate, in which case the client falls back to the bootstrap phase to fetch updated certificates.

ConnectDnsResolvingFailed

The client cannot resolve the DNS query for the Device Management server URL addresses. It continues to retry until it resolves the DNS, then continues the connection process.

ConnectorFailedToStoreCredentials

The client cannot store the device credentials in the secure storage. Check the memory card (in Mbed OS). If it is corrupted, please format it.

ConnectorFailedToReadCredentials

The client cannot read the device credentials from the secure storage. Check the memory card (in Mbed OS). If it is corrupted, please format it.

ConnectorInvalidCredentials

The client failed to get the proper bootstrap credentials from the secure storage. Try to factory reset the secure storage, then try the operation again.

The client returns an Invalid Parameter error

Sometimes, your client application might return MbedCloudClient::ConnectInvalidParameters while registering with Device Management.

In factory mode, this can happen because you're using a wrong URI format to access the bootstrap service or LwM2M server:

• For bootstrap, the URI format is: coaps:\\<mbed- bootstrap-server-url>:5684?aid=<your-account-id>.
• For LwM2M, the URI format is: coaps:\\<mbed-LWM2M-server-url>:5684?aid=<your-account-id>.

Reflash these values with the factory configurator client (FCC), and run your application again.

The client prints RTX error (Mbed OS only)

If you see:

• RTX error code 0x00000001 .. in your console, it means your application has run out of stack memory.

  Device Management Client handles its asynchronous operation through a separate thread. That thread has been assigned 8 kB of its own stack space, but for some applications, this might not be enough. You can increase the stack from your application's mbed_app.json file, by modifying the stack size value from 8192 to some higher value:

  "nanostack-hal.event_loop_thread_stack_size": <8192>,
  

  Remember to check your hardware configuration - it must have enough memory to handle a bigger stack size.

• If you compiled your application as a debug version, it will require more flash memory than a release version - typically 1.5 to 2 times more. For debugging purposes, you may need to select hardware that is less constrained than your normal deployment devices.

Request frequency issues

Device Management provides sufficient capacity to handle REST API requests. When the frequency of issued requests is above a threshold set to protect our system, our system returns an error with code 429. If you receive this error, please pause request execution for 60 seconds. You can then resume normal work.

Firmware Update Error Handling

During its lifetime, the device can report a number of errors related to firmware update, including:

• Internal client errors, which the client logs if the debugging log is turned on.

• Errors the client logs even when debugging is turned off.

• Errors the client reports to the cloud using the 10252/0/3 UpdateResult LwM2M resource.

  For more information about errors the client reports to the cloud, see Event log codes.